×
  • English
  • Swedish
  • German
  • French

HTC Superfloor™

Grinding and polishing guides

HTC Superfloor™

HTC Superfloor™ finish is possible to create on both existing concrete floor with or without coatings and for new buildings in the construction phase. For the existing floors the final appearance is dependent upon how the concrete floor once was produced with regard to the colour of the cement, the type and amount of aggregate and how much of the aggregate it is possible to expose after grinding.

Existing concrete floors can often be grinded to the quality of a HTC Superfloor™ using diamond tools and concrete polishers from HTC. For newly casted concrete floors the different possibilities for create an elegant floor are endless. Read more about HTC Superfloor™ in the Floor Solutions section.

To create an HTC Superfloor™ you start with a common concrete surface. The first step is to remove possible old coatings on the surface. This is described in the section Floorprep. When this is done you continue with the correct guides for HTC Superfloor™ depending on the type of concrete.

Check out our concrete polishers and grinders under the Products section.

  • HTC Superfloor™

    Platinum

    The intention of the first grinding step is to create a surface that is as flat as possible. It is the foundation for a good end result. All subsequent grinding steps must remove the scratches from the previous grinding step. Depending on the properties of the floor all steps might not be needed. Resin bonded diamond tools should be used with flexible tool holder.

    • Gold
      Gold Metal
    • Grey
      Grey Metal
    • Brown
      Brown Metal
    • Chemical
      HTC Grouting
    • Black
      Black Metal
    • Chemical
      HTC Cure+
    • Black
      Black Resin
    • Blue
      Blue Resin
    • Red
      Red Resin
    • White
      White Resin
    • Yellow
      Yellow Resin
    • Green
      Green Resin
    • Chemical
      HTC Stain Protection
    Flexible tool holder
  • HTC Superfloor™

    Gold

    Coarse/flat grinding is not included in this concept. This requires that the surface is already smooth and flat, otherwise – use the grinding process for HTC Superfloor Platinum. All subsequent grinding steps must remove the scratches from the previous grinding step. Depending on the properties of the floor all steps might not be needed. Resin bonded diamonds should be used with flexible tool holder.

    • Gold
      Gold Metal
    • Chemical
      HTC Grouting
    • Black
      Black Metal
    • Chemical
      HTC Cure+
    • Black
      Black Resin
    • Blue
      Blue Resin
    • Red
      Red Resin
    • White
      White Resin
    • Yellow
      Yellow Resin
    • Green
      Green Resin
    • Chemical
      HTC Stain Protection
    Flexible tool holder
  • HTC Superfloor™

    Silver

    The intention of the first grinding step is to create a surface that is as flat as possible. It is the foundation for a good end result. All subsequent grinding steps must remove the scratches from the previous grinding step. Depending on the properties of the floor all steps might not be needed. Resin bonded diamonds should be used with flexible tool holder.

    • Gold
      Gold Metal
    • Grey
      Grey Metal
    • Brown
      Brown Metal
    • Chemical
      HTC Grouting
    • Black
      Black Metal
    • Chemical
      HTC Cure+
    • Black
      Black Resin
    • Chemical
      HTC Stain Protection
    Flexible tool holder
  • HTC Superfloor™

    Bronze

    This is a process for honing an already smooth and even concrete surface. It works good on intensely steel troweled concrete and hard concrete or dry shake toppings. Depending on the properties of the floor all steps might not be needed. Resin bonded diamonds should be used with flexible tool holder. Fenix pads usually work best.

    • Brown resin
      Brown Resin
    • Black
      Black Resin
    • Chemical
      HTC Cure+
    • Blue
      Blue Resin
    • Red
      Red Resin
    • Chemical
      HTC Stain Protection
    Flexible tool holder
×

Multimedia

  • HTC Superfloor
    HTC Superfloor™ process

    Platinum concept step-by-step Platinum concept step-by-step

    This movie describes the basic process of grinding an HTC Superfloor™. For this job a radio controlled HTC DURATIQ RX6 was used.

Downloads

Related Pages

  • Create pdf
  • Tool search
  • Book a demo